Here's a new Right Hand Front Brake Wheel Cylinder (x1) (0.8") for the following models from Commer-

COMMER

Commer Cob     (**From 1958- 65**)

(These are for the Audax shaped Commer Cob (1390cc OHV) as pictured).

(Not for the earlier Minx Mk8 shaped (1265cc Side Valve) Commer Cob Mark 1 of 1954- 57).

 These Cylinders were remade to the original Lockheed design using Genuine old stock samples.

(Original Part No/s 81281 - 81282). 

They have replaceable seals and are identical to the originals.

My cylinders are a Fair Price & they're available to Everyone.

Here's a new pair of Front Brake Discs (x2) (262mm) for the following models from Hillman-

HILLMAN

Hillman Super Minx   (Ser 2 3 4 5)     (1962- 67)

(** Not for the earlier Super Minx Ser.1 of 1961- 62 which had Front Drums **)

Read and understand the description, know which car you have.

Here's a new set of Front Brake Pads for the following models from Hillman -

HILLMAN

Hillman Super Minx     (From 1962- 68)

(Ser 2 3 4 5)

(Not for the earlier Super Minx Ser.1 which had Front Drums)

Here's a set of Front Brake Pads for the following models from Hillman -

HILLMAN

Hillman Minx   (Ser.5 & 6)

(1965- 67 Only)

(Earlier Minxes had front drums- Not for the later Square New Minx of 68- ).

You might also want some Brake Caliper Pistons & Seals, Master Cylinder Kits or Wheel Cylinder Kits for these models as well.

Here's a new Clutch Master Cylinder (5/8") for the following models from Hillman-

HILLMAN

Hillman Super Minx Ser.2 {Late}   (1592cc)  (**From 1963- 64**)

Hillman Super Minx Ser.3             (1592cc)  (1964- 65)

Hillman Super Minx Ser.4             (1725cc)  (1965- 67)

(** Suits From Ch. No/ B1308380 which part way through Ser.2 up until the end of Super Minx in 1967 **)

(** Not for earlier Super Minx's which used a 0.70" or 0.75" Clutch Master **)

(** Yes this suits Super Minx 's with the both old gearbox {Pre Oct 64} or the newer all Syncro gearbox {From Oct 64} **).

(NOTE - Minx & Super Minx are NOT the same car**)

(NOTE - As pictured this has Plastic Reservoir). 

(NOTE - The Pushrod is not included - Re-use the old one) 

Here's a new set of Front & Rear Brake Wheel Cylinders (x6) for the following models from Hillman-

HILLMAN

Hillman Minx Ser.1              (1956- 57)

Hillman Minx Ser.2              (1957- 58)

Hillman Minx Ser.3             (1958- 59)

Hillman Minx Ser. 3a          (1959- 60)

Hillman Minx Ser. 3b         (1960- 61)

Hillman Minx Ser. 3c         (1961- 63 Only)

(**Not for any later Minx's from 1963 onwards which all had Front Discs**)

(** Out of Interest - From 1964 onwards they switched from these Manual Adjusting Rear Cylinders to completely different Self Adjusting Rear cylinders. That is -They all had Front Discs anyway by the time they stopped using the rear cylinders I'm supplying **)

(** ie The Minx was never made with Front Drums and the later Self Adjusting Rear Cylinders**)

These are only for the Audax shape which is the car pictured.

(Not for earlier the earlier California shaped Minx Mk7 / Mk8 of 1954- 57)

These Cylinders were all remade to the original Lockheed design using Genuine old stock samples. They all have Replaceable Seals.

(Original Part No/s 81281, 81282 & 103893).

NOTE - Fit the Rear Cylinders from the **DRUM SIDE** They will not go through the back plate if you try to push them through from the **AXLE SIDE** 

My cylinders are a Fair Price & they're available to Everyone.

Here's a new set of Front or Rear Brake Shoes for the following models from Hillman -

HILLMAN

Hillman Minx    (1956- 60 Only)

(Series 1, 2 ,3, 3a Standard Only)

( **Not for the 3a Delux or 3a Easidrive which has 9" x 1.75" shoes - Measure them if unsure **)

( ** Not for the later 3b or 3c Minxes or anything after them which also used larger 9" x 1.75" shoes**)

(** Not for the similar shaped Singer Gazelle  / Vogue etc **)

NOTE - 9" Brakes refers to the internal Drum diameter. It does not refer to the length / circumfernce of the Brake Shoe.

Don't think the Gazelle / Minx / Super Minx / Rapier / Alpine / Vogue are all the same - THEY'RE NOT.

If you need enough shoes for the Front & Rear then change the Quantity to x2 at checkout.

Here's a new set of Front OR Rear Brake Shoes for the following models from Hillman -

HILLMAN

Hillman Minx    (**From 1948- 56 Only **)

(Mk2, Mk3, Mk4, Mk5, Mk6, Mk7 & Mk8)

(Not for the later Series 1 - 6 Minx of 1956- 67).

(**Don't think the Gazelle / Rapier / Sceptre / Super Minx / Vogue / later Minx's are the same . They're Not **)

If You need enough shoes for the Front & Rear then change the Quantity to x2 at checkout.

(Cars pictured are a Minx Mk2 and Minx Mk8).

Here's a new Axle Set of Front Brake Wheel Cylinder Repair Seals Kits (x4) for the following models from Hillman-

HILLMAN

Hillman Minx Ser.1   (1956- )

Hillman Minx Ser.2  (1957- )

Hillman Minx 1500cc  (1958- )

Hillman Minx Ser. 3,3a,3b,3c (1959- 65)

From 1965 they fitted Front Discs instead of Front Drums & Wheel Cylinders. 

Here's a new Rear Brake Hose Pipe (x1) for the following models from Hillman -

HILLMAN

Hillman Super Minx (Ser.1)    (1961- 62) (** RHD Only on Ser.1**)    

Hillman Super Minx (Ser.2)    (1962- 64)

Hillman Super Minx (Ser.3)    (1964- 65)

Hillman Super Minx (Ser.4)    (1965- 67)

(** Only the Super Minx - Not for the ordinary Minx **)

(** Don't think the Vogue / Gazelle / Minx / Rapier etc are all the same - They're Not **)

 You require x1 Rear Hose per car. If you buy x2 I'll assume you want them and I'll send them Both.

Here's a new pair of new Front Brake Hoses (x2) for the following models from Hillman -

HILLMAN

Hillman Super Minx (Ser.1) (1961- 62)

(** Only for Right Hand Drive **)

(** Only for the Ser.1 which had Front Drums - Not for later Disc models**)

(** Not for the ordinary Minx - Only ther Super Minx**)

Take the time to read and understand this, it's taken me time and effort and skill to get this description correct.