Here's a new pair of Front Brake Hoses (x2) for the following models from Ford -

FORD

Ford 400e Thames (Van & Pickup)     (1957- 65)

(Suits 10cwt, 12cwt & 15cwt versions).

Not the same as the smaller Anglia shaped Thames or the larger Thames Trader Lorry.

Here's a new Rear Wheel Bearing Kit (With Fitting Collar) for the following models from Ford -

FORD

Ford Anglia 105e, 123e   (** 1959- 66 Only **)

If you are unsure which axle you have please get your old bearing out to compare.

This bearing has no Rubber O Ring round the outside edge (The later bearing does).

This bearing sticks out either side where the central shaft goes in, the later bearing sticks out only on one side.

Here's a new Clutch Hose Pipe for the following models from Ford -

FORD

Ford 100e Anglia,  Prefect & Popular  (1954- 59 Only)

(** Side Valve Engines Only **)

Here's a new pair of Front Brake Hoses (x2) for the following models from Ford -

FORD

Ford Zephyr Mk2     (1956- 62)

Ford Zodiac Mk2     (1956- 62)

Here's a pair of Front Brake Hoses (x2) for the following models with Front Drums from Ford -

FORD

Ford Cortina Mk1 (1962- 66)

(**With Front Drum Brakes**)

Here's a pair of Front Brake Hoses (x2) for the following models from Ford -

FORD

Ford Escort Mk1    (1968- 74)

(** Only where Front Drum Brakes are used **)

Here's a new Rear Brake Hose (x1) for the following models from Ford-

FORD
 

Ford Zephyr Mk1     (1951- 55) 

Ford Zodiac Mk1     (1951- 55) 

Ford Consul Mk1    (1951- 55)

(x1 Rear Hose Required per car - If you buy x2 I'll assume yoo want them & I'll send them both).

Here's a new pair of Front Brake Hoses (x2) for the following models from Ford -

FORD

Ford Zephyr Mk3     (1962- 66)

Ford Zodiac Mk3     (1962- 66)

Here's a new Rear Brake Hose (x1) for the following models from Ford-

FORD
 

Ford 100e Anglia, Prefect & Popular (1954-59) 

Here's a new pair of Front Brake Hoses (x2) for the following models from Ford -

FORD

Ford 100e            (Anglia, Prefect & Popular)   (1954- 59)

Ford 107e, 108e  (Anglia, Prefect & Popular)   (1959- 62)

(Only for the 100e shape - Not for the 105e Anglia of 1959- 68)

Here's a new Rear Brake Hose (x1) for the following models from Ford -

FORD
 

Ford Anglia 105e  (1959- 68)

(Suits Van, Saloon & Estate) 

(x1 Rear Hose Reuired per car)

Here's a new pair of Front Brake Calipers (x2) for the following models from Ford-

FORD

Ford Zephyr Mk4 (1966- 72)

(V4 & V6) 

Ford Zodiac Mk4  (1966- 72)

(V4 & V6)

(** These will not fit the earlier Mk2 or Mk3 Zephyr / Zodiac models of 1960- 66 **)

(** DO NOT buy these for Anything Other Than The Car Pictured- Which is a Zephyr / Zodiac MkIV of 1966- 72 **)

These calipers come complete with the pistons and seals already assembled, they do not include Brake Pads or the Pad Fitting Pins / Shims. 

These Calipers have Type 16PB Pistons.                  (Stepped top Piston and Metal Ring)

 Your original Calipers may have Type 16P Pistons.  (Flat Top Piston with no Metal Ring)

There are two varieties of piston / seal as Girling improved the design with the 16pb from 1968. 

There’s no difference in braking between 16p & 16pb as the pistons are the same diameter.

If you just want one side - talk to me.

***    NOT AVAILABLE TO NORWAY , SWITZERLAND, MALTA , CYPRUS or CANARIES ***

Here's a new (**Stainless Steel Sleeved**) Clutch Slave Cylinder Assembly (7/8") for the following models from Ford / Lotus-

FORD / LOTUS

Lotus Cortina Mk2        (1966- 70)

(1300, 1500, 1600, 1600GT, 1600E & Lotus)

This is a completely New part with a Stainless Steel sleeve. 

It's not a manky rotten Old thing that's just been sleeved up.

This has the correct 7/8" bore for the Cortina Mk2.

Don't pay the same price for one that's not Stainless Steel - This is the very finest part you can buy.

(** Suits LHD & RHD **) 

Here's a set of new Rear Brake Shoes (** For Lockheed Brakes **) (9"x 1.75") for the following models from Ford -

FORD

Ford Escort Mk1 RS1600   (Jan 73 - Jan 75)

(** Lockheed Brakes Only **)

Ford Escort Mk1 Mexico 1.6  (Jan 73 - Jan 75)

(** Lockheed Brakes Only **)

*** LOCKHEED TYPE BRAKES - SEE THE PICTURE **

These Fords were fitted with either Girling or Lockheed brakes. 

Girling Brakes          = Single Piston Wheel Cylinder (Piston at One End of Sliding Cylinder)

                                   = Two Brake Springs per Wheel (x1 Really Long & x1 Really Short).

Lockheed Brakes    = Double Piston Wheel Cylinder (Piston at Each End).

                                  = Three Brake Springs per Wheel.

Note - The Master Cylinder and Front Brakes are always Girling so reading what is says on the Master Cylinder is not accurate enough. You are advised to compare the picture or call for advice.

Don't just buy this without finding out which type you have - Look at the picture.

Here's a new (**Stainless Steel Sleeved**) Clutch Slave Cylinder Assembly (7/8") for the following models from Ford -

FORD

Ford Cortina Mk2        (1966- 70)

(1300, 1500, 1600, 1600GT, 1600E & Lotus)

This is a completely New part with a Stainless Steel sleeve. 

It's not a manky rotten Old thing that's just been sleeved up.

This has the correct 7/8" bore for the Cortina Mk2.

Don't pay the same price for one that's not Stainless Steel - This is the very finest part you can buy.

(** Suits LHD & RHD **) 

Here's a new Nylon Clutch Hose Pipe (x1) for the following models models from Ford-

FORD

Ford Cortina Mk2    (** RHD Only **)   (1966- 70)

(1300, 1500, 1600, 1600GT & 1600E Only)

(** Not for Left Hand Drive cars **)

(** Not for the Lotus model **)

(** Not for the Cortina Mk1 or anything else which is not listed above **)

(** Because people don't read my descriptions I may cancel the sale without notice if you give and address where the cars are Left Hand Drive **).

Yes this has the correct 7/16" threads at each end.

Don't buy anything else because its cheaper - Then start moaning when it wont fit.

Here's a new Clutch Master Cylinder (0.7") for the following models from Ford -

FORD

Ford Cortina Mk2    (1966- 70)

(1300, 1600, 1600GT, 1600E & Lotus)

(Suits LHD & RHD) 

** You can buy a Cheapo Master Cylinder on ebay which has the wrong pipe thread for £22 - Then you can spend all day trying to find an adaptor.

** Get it fitted then figure out the your bargain £22 master cylinder is 0.75" whereas it should be 0.7" - This means 18% harder clutch pedal.

OR

**You can buy this, fit it and drive off within half an hour - You decide**

Rod can be removed and swapped if required.

Better Quality than all the others i have seen listed - Look at the picture....

(** Not for the Ford Cortina Mk1 **)

(** Not for the Ford Cortina Mk3/4/5 **)

(** Not for the Ford Corsair **)

Here's a new Brake or Clutch Master Cylinder (5/8") for the following models from Ford -

FORD

Ford Anglia 105e  (1959- 68)

(Suits Saloon / Van / Estate & Super Anglia)

You might want x2 of these as they suit the Clutch and Brake Master

Correct 5/8th bore & correct thread for the pipe.

NOTE- You will have to swap and re-use the old Pushrod. It's only hel ionm place by a circlip.

Better Quality than all the others i have seen listed - Look at the picture....