Here's a new Sump Gasket Set for the following models from Morris -

MORRIS

Morris 8  (Ser.1,2&E)    (1935- 48)  

(** Side Valve 918cc **) 

Here's a new set of Front Brake Wheel Cylinders (x4) for the following models from Austin / Morris -

AUSTIN / MORRIS

Austin J4 Van                (1960- 74)

If in doubt have a look at the picture.

Here's a new Axle Set of Front Brake Wheel Cylinder Repair Seals Kits (0.8") (x4) for the following models from Morris-

MORRIS

Morris JU250 Van       (1967- 74) 

(Do NOT buy these for anything other than the exact models listed above)

(Do NOT buy these for anything other than what I say it will fit)

NOTE- If you're unsure of your model then look on the Chassis Plate - It will say JU250 very clearly.

Here's a new Rear Wheel Bearing Kit (x1) for the following models from Morris -

MORRIS

Morris Oxford MO        (1949- 54)

Here's some Bonnet Seals suitable for the following models from Morris -

MORRIS

Morris Minor & Traveller (1948- 71) 

The length supplied is enough for one Minor (Both sides) with a small bit extra, you just cut it to the exact requirements.

The photo shows the end profile of this seal so you can see how it goes.

These are new and unused seals, they are recently manufactured and are of excellent quality as you can see from my feedback.

These fit on the body one each side, here's enough for one car.

Here's a pair of new Front Brake Hoses (x2) for the following models from Morris -

MORRIS

Morris 8 (Ser. E Only)  (From 1939- 48) 

(** Not for the earlier Morris 8 Ser 1 & 2 **)

Morris 8 (Ser. Z Van)    (From 1939- 50 Only) 

(** Only up to Ch.40,816, it's different from 1951- 53)

Here's a new Clutch Release Bearing (With Fitting Clips x2) for the following models from Morris -

MORRIS

Morris 8  (Seri. 1 & 2)    (1935- 38)                

Morris 8  (Ser. E)          (1938- 48)    

Here's a new Rear Brake Hose (x1) for the following models from Morris -

MORRIS

Morris 8 (Ser. E Only)      (From 1939- 48) 

(** Not for the earlier Morris 8 Ser 1 & 2 **)

Morris 8 (Ser. Z Van)      (From 1939- 50 Only) 

(** Only up to Ch. 40816, it's different from 1951- 53)

Here's a new Front OR Rear Brake Wheel Cylinder (x1) (7/8") for the following models from Morris-

MORRIS

Morris 8 Saloon  (Ser. 1 ,2 & E)       (1935- 48)

Morris Z Van                                     (1939- To About 1951)  

(** For Z Van - See Note Below **) 

(** Morris Z Van - Suits front & rear for models up to about 1951 which will have x1 Steel Wheel Cylinder on each Wheel. If you've got a later 51-53 model then you'll have x2 Aluminium wheel cylinders on each Front each and completely diferent Aluminium cylinders on the rear - These won't fit either the front or rear of later Z Vans of 1951- 53).

If you want enough for the font AND rear brakes then change the quantity to x4 at checkout.

(Original Part Number was Lockheed 3905 OR 12875). 

(The background picture is not included and is no longer available, it’s not fitting instructions and does not indicate the originality of these part or which cars this part will or won’t fit – See the Text).

Here's a new pair of Rear Brake Wheel Cylinders (x2) for the following models from Morris -

MORRIS 

Morris J Type Van        (1949- 57)

Morris JB Type Van     (1957- 61)

(Not for the later Morris J2 Van) 

Here's a new pair of Front Wheel Cylinders (x2) for the following models from Morris -

MORRIS

Morris J Type Van      (1949- 57)

Morris JB Type Van   (1957- 61)

(Not for the Morris J2 Van).

These models need x4 Front Wheel Cylinders, you are bidding for a pair here which is enough to do one front wheel.

These are the same left and right.

You'll need a second pair if you want to do both front wheels.

Here's a new Brake Master Cylinder Repair Seals Kit (7/8") for the following models from Morris  -

MORRIS

Morris J Type Van    (1949- 57)

Morris JB Van          (1957- 61)

(Not for the J2)

Here's a new Snail Cam Brake Adjuster (x1) for for the following models from Morris -

MORRIS

Morris J Type Van    (1949- 57)

Morris JB Van          (1957- 61)

(Not for the later Morris J2 Van).

As you can see in the picture the 'Mask' is included with the Snail Cam.  

The adjuster is shown fitted onto the end of a Brake Shoe, that Brake shoe is not included in the price.

There are x6 of these on a car - That's x4 on the Front Brakes and x2 on the Rear Brakes.

You can buy any amount from 1 - 6. 

Here’s a new set of Front OR Rear Brake Shoes for the following models from Morris –

MORRIS

Morris J Type Van     (1949- 57)

(Not for the later Morris J2 Van)

If you want a set of shoes for both the Front & Rear - Please change the quantity to x2 at checkout.

Here's a new Head Gasket Set (Made in UK) for the following models from Morris -

MORRIS

Morris Minor  (1952- 71)

(803cc, 948cc & 1098cc)
 

(That's all Minors except the earlier Side Valve 918cc engined Minor of 1948- 52).

Here's a new Sump Gasket Set for the following models from MG -

MORRIS

Morris 10 (Series M) (1140cc)     (1938- 49)

Not for the earlier Morris 10/4.

Not for the earlier Morris 10/6.

This is a Conversion Set so you get all the gaskets for the lower half of the engine.

Here's a new Rear Hub Wheel Bearing Kit (x1) including Oil Seals - for the following models from Morris-

MORRIS

Morris Isis (2.6 Litre)   (Ser.1 & 2)  (1953- 56)

Here's a new Clutch Fork Arm Gaiter for the following models from Morris -

MORRIS

Morris Minor  (**From 1952- 71**)

(Suits 803cc, 948cc & 1098cc)

Here's a new Timing Chain Kit for the following models from Morris -

MORRIS

Morris Minor    (803cc, 948cc & 1098cc)        (1952- 71)

(** Not for the earlier Side Valve Minor of 1948- 52 **)

Included in this kit it the following -

Timing Chain 

Felt Oil Seal for Early Timing Cover

Rubber Oil Seal for Late Timing Cover

Tensioner Rings x2

Crankshaft Lock Tab

You need this kit for any engine rebuild, the oil seal will have gone hard and the timing chain will have stretched making it noisey and more likely to break.

Here's a new set of Front OR Rear Brake Shoes (x4) for the following models from Morris -

MORRIS

Morris Oxford MO   (**Not for Van & Pickup**)  (1949- 54)

(** Saloon Car only - Not for the Morris Oxford MO Van & Pickup which used Bigger brakes **) 

(** These are only for the Morris Oxford MO as pictured - Which looks like a big Minor **) 

(** Don't buy these for any later Morris Oxfords - They won't fit  **) 

If you need enough shoes for the Front & Rear then change the Quantity to x2 at checkout.

Here's a new set of Front OR Rear Brake Shoes for the following models from Morris -

MORRIS

Morris Cowley 1200cc   (**1954- 56 Only**)

(** Cowley 1200cc Only**)

(** Not for the later Cowely 1500cc of 1956- 58 which has bigger brakes **)

If you need enough shoes for the Front & rear then change the Quantity to x2 at checkout.

Here's a new set of Front Brake Shoes for the following models from Morris-

MORRIS

Morris Minor 1098cc  (**From Oct 62- 71**)

(**These are for 8" diameter drums fitted on the 1098cc model**)

(**Not for earlier models made before Oct 62 which used 7" drums**)

Here's a new pair of Front Engine Mounts (x2) for the following models from Morris -

MORRIS

Morris Minor    (1952- 71)

(803cc, 948cc, 1098cc)

(Includes Van & Pickup)

Minors before 1952 used the gearbox mounts as engine mounts - see the picture if unsure.

Here's a new Clutch Fork Arm Gaiter for the following models from Austin -

AUSTIN

Austin A40 Cambridge             (1954- 56)

Austin A50 Cambridge             (1954- 57)

Austin A55 Cambridge Mk1     (1957- 59) 

Austin A55 Cambridge Mk2     (1959- 61) 

Austin A60 Cambridge            (1961- 71) 

(Suits 1200, 1500 & 1622 versions of the above models).

(** Not for the earlier A40 Devon, A40 Dorset, A40 Somerset or Jensen A40 Sports or the later A40 Farina**).

Here's a new Brake Master Cylinder Repair Seals Kit (7/8") for the following models from Morris -

MORRIS

Morris 8 Saloon  (Ser 1 & 2)            (Oct 34- 39)  

Morris 8 Saloon  (Series E)              (1939- 48)     

Morris 8 Van      (Series Z)                (1939- 53)      

(Includes Saloon / Tourer  & Ser 1 & 2 Van but not GPO Van) 

(** Made in England **)

Here's a new pair of Universal Joints (x2) for the following models from Morris -

MORRIS

Morris 8             (1935- 48)

(Includes Ser.1,2 E & Z Van)

These come complete with all the required circlips so it's an easy fitting job -

Symptoms of worn joints are - A 'clonk' noise under power / pulling away OR continued clonking if the joints have deteriorated badly.

Here's the exact measurements of the joints -

Cup diameter 2.382cm, Joint Diameter 6.130cm

Here's a new Head Gasket Set for the following Side Valve models from Morris -

MORRIS

Morris Z Van       (**From 1939- 53**)

(** 918cc Side Valve **) 

Not for the older shape Morris 8 Van - Only suits the one shown on the picture.

Here's a new Ignition Coil for the following models from Morris -

MORRIS

Morris Minor       (1948- 67 Only )

It's a Non-Ballast coil for use with Screw-In Leads (Not Push- In Leads).

(** Check if you have  Push In or Screw In Leads **)

*** NOTE - This may be coloured Black or Silver depending on what the supplier sends me ***

This function of this coil is to generate the 000's of volts required by your spark plugs, they deteriorate with age and the insulation between the wires inside can breakdown and therefore the coil needs replacing once in a while.

Here's a new Clutch Master Cylinder (5/8") for the following models from Morris -

MORRIS

Morris Oxford (Ser.5)    (1959- 61 Only)

(** Not for the later Morris Oxford Ser.6 1622cc of 1961- 71 which used a larger 7/8" Slave Cylinder **)

This is the Correct one -

1) Correct Rod
2) Correct 5/8" Bore
3) Correct Pipe Thread

|

Here's a new Head Gasket Set & Sump Gasket Set (ENGINE GASKET SET) for the following Side Valve models from Morris -

MORRIS

Morris 8       (From 1939- 48)

(** Series E Only **)

(** This will not suit the earlier Morris 8 Series 1&2 of 1935- 39 which has a smaller bore **)

(** The Morris 8 Series E is easily identified as the headlights are built in - As the picture**)

The Morris 8 Ser 1&2 has the Morris UB engine.

The Morris 8 Series E has the USHM engine.

Here's a new pair of Gearbox Mounts (x2) for the following models from Morris -

MORRIS

Morris JB Van  (1500cc Petrol) (1957- 61) 

(Not for the later Morris JB Van which used square shaped gearbox mounts)

(I have no info on the earlier J Type Side Valve van of 1949- 57)

Here's a new pair of Front Engine Mounts (x2) & Gearbox Mounts (x2) for the following models from Morris -

MORRIS

Morris Minor    (From 1952- 71)

(803cc, 948cc, 1098cc)

(Includes Van & Pickup)

Before 1952 the Side Valve model used the different Engine Mounts.

Here's a new Brake Master Cylinder (3/4") for the following models from Morris -

MORRIS

Morris Oxford Mk5     (1959-  61 Only)

(You'll need to re-use your old rod, it's an easy swap as it's only held on by a circlip).

Here's a new Rear Brake Hose (x1) for the following models from Morris  -

MORRIS

Morris Oxford (Ser.5)  (1959- 61 Only)

Here's a pair of Front Brake Hoses for the following models from Morris -

MORRIS

Morris Oxford MkV (1959- 61)

Here's a new Head Gasket Set & Sump Gasket Set (ENGINE GASKET SET) for the following models from Morris-

MORRIS

Morris Cowley 1200cc      (1954- 55)

Morris Cowley 1500cc      (1955- 59)

Here's a new Head Gasket Set & Sump Gasket Set (ENGINE GASKET SET) for the following models from Morris-

MORRIS

Morris Oxford Ser 2                (1489cc)      (1954- 56)

Morris Oxford Ser 3                (1489cc)      (1956- 59)

Morris Oxford Ser 4 Estate   (1489cc)      (1957- 60)

Morris Oxford Ser 5               (1489cc)      (1959- 61)

Morris Oxford Ser 6              (1622cc)      (1961- 66 Only) (** Different from 66 **)

Here’s a new Head Gasket Set for the following models from Morris-

(B Series Engines 1500cc & 1600cc)

MORRIS

Morris Oxford Ser 2                (1489cc)      (1954- 56)

Morris Oxford Ser 3                (1489cc)      (1956- 59)

Morris Oxford Ser 4 Estate   (1489cc)      (1957- 60)

Morris Oxford Ser 5               (1489cc)      (1959- 61)

Morris Oxford Ser 6              (1622cc)      (1961- 66 Only) (** Different from 66 **)

(Not for 1600's with Engine Numbers 16AA, 16GF which are 5 bearing crank from 1966- )

Contains all the gaskets required to remove / Replace the Cylinder Head.

Check your engine number if you have the 1600cc. 

Here's a new Head Gasket Set & Sump Gasket Set (ENGINE GASKET SET) for the following models from Morris-

MORRIS

Morris JB Van      (From 1957- 61)

(1489cc OHV Petrol Engine)

*** Not for the earlier Morris J Type Van of 1949- 57 which had a Side Valve Engine ***

Here’s a new Head Gasket Set for the following models from Morris-

AUSTIN / MORRIS

Morris J2 Van           (1956- 66 Only)   (** Different from 66 **)

(1489cc & 1622cc OHV Petrol Engine)

(Not for the Side Valve found in other the earlier J Type Morris).

(For the 1600, only suits Engine Numbers 16AMW, 16GE & 16RA which are 3 bearing crank engines from 1961- 67)

(Not for 1600's with Engine Numbers 16AA, 16GF which are 5 bearing crank from 1966- )

Contains all the gaskets required to remove / Replace the Cylinder Head.

Check your engine number if you have the 1600cc. 

Here's a new Head Gasket Set & Sump Gasket Set (ENGINE GASKET SET) for the following models from Austin / Morris-

AUSTIN / MORRIS

Morris J2 Van           (1956- 66 Only)   (** Different from 66 **)

(1489cc & 1622cc OHV Petrol Engine)

(Not for the Side Valve found in other the earlier J Type Morris).

(For the 1600, only suits Engine Numbers 16AMW, 16GE & 16RA which are 3 bearing crank engines from 1961- 67)

(Not for 1600's with Engine Numbers 16AA, 16GF which are 5 bearing crank from 1966- )

Check your engine number if you have the 1600cc. 

Here's a new Head Gasket Set & Sump Gasket Set (ENGINE GASKET SET) for the following models from Austin / Morris -

AUSTIN / MORRIS

Austin / Morris J4 Van     (1960- 66 Only)  (** Different from 66 **)

(1622cc Petrol Engine)

(For the 1600, only suits Engine Numbers 16AMW, 16GE & 16RA which are 3 Bearing Crank engines from 1961- 66).

(Not for 1600's with Engine Numbers 16AA, 16GF which are 5 Bearing Crank from 1966- 71).

Check your engine number if you have the 1600cc. 

Here's a new Boot Rubber Seal for all the following models from Morris -

MORRIS

Morris Minor Saloon (1948- 71)

(Not for the Rear Doors on the Traveller / Estate / Van).

The length supplied is enough for one Minor with a small bit extra, you just cut it to the exact requirements.

Some early Minors used a Glue on Boot Seal - It's Rubbish. This press on seal will replace it.

The photo shows the end profile of this seal so you can see how it goes, easy to fit - just press on.

Here's a new Sump Gasket Set for the following models from Morris -

MORRIS

Morris Z Van     (1939- 53)  

(** Side Valve 918cc **) 

Here’s a new Rear Brake Adjuster for the following models from Morris -

MORRIS

Morris Ital 1300 / 1500 Diesel (1980- 84)

Morris Ital 2000 Auto               (1980- 82)

Morris Ital Van                          (1982- 84)

Morris Marina 1300 / 1500 Diesel (Single Line Brakes) (1971-71)

Morris Marina 1300 / 1500 Diesel (1975-78)

Morris Marina 1300 / 1500 Diesel 1800 (1978-80)

Morris Marina 1800(1975-78)

Morris Marina 440 Van 1100 1300 (1978-82)

Morris Marina 575 Pickup Van (1978-82)

Morris Marina 7 cwt Van / 10 cwt Van (1974-78)

(** Excluding self Adjusting Brakes fitted aprox 1972-73 **)

You need one per wheel, you are bidding for one here.

Here's a new Clutch Kit (6.25") for the following models from Morris  -

MORRIS

Morris 8  (Ser. 1 & 2)   (1935- 38)                

Morris 8  (Seri. E)        (1938- 48)  

This is a new part - Not reconditioned.

***    NOT AVAILABLE TO NORWAY , SWITZERLAND, MALTA , CYPRUS  ***

Here’s a new Engine Set of Piston Rings (STD, 5 Ring Type, 0.063"Wide) (Made in the USA by Grant) for the following models from Morris –

(1489cc Engines Only)

MORRIS

Morris J2      (1956- 65) 

*** These cars were fitted with either 4 Ring Pistons or 5 Ring Pistons. Get them out and look. This set is for the 5 Ring Pistons ***

*** These cars were fitted with a choice of two compression ring widths, either 0.063" or 0.078". Get them out and measure. This set is the for the 0.063"wide compression rings **

*** This set is STD (Standard Size), ensure you know the size you require before ordering **

This set contains four times - 

x3 Compression Rings 0.063" wide.

x2 Oil Rings 0.156" wide

The picture shows them in their packet as they are all in order. 

Here’s a new Engine Set of Piston Rings (STD, 5 Ring Type, 0.063"Wide) (Made in the USA by Grant) for the following models from Morris –

(1489cc Engines Only)

MORRIS

Morris Oxford (Ser 2 3 4 5)          (1954- 61 Only)

*** These cars were fitted with either 4 Ring Pistons or 5 Ring Pistons. Get them out and look. This set is for the 5 Ring Pistons ***

*** These cars were fitted with a choice of two compression ring widths, either 0.063" or 0.078". Get them out and measure. This set is the for the 0.063"wide compression rings **

*** This set is STD (Standard Size), ensure you know the size you require before ordering **

This set contains four times - 

x3 Compression Rings 0.063" wide.

x2 Oil Rings 0.156" wide

The picture shows them in their packet as they are all in order. 

Here’s a new Engine Set of Piston Rings (STD, 5 Ring Type, 0.063"Wide) (Made in the USA by Grant) for the following models from Austin / Morris -

(1489cc Engines Only)

AUSTIN /  MORRIS

Austin A152 Series            (1955- 61) 

(Omnitruck, Omnivan & Omnicoach) 

Austin J4 10-15 Cwt Van  (1955- 61)

*** These cars were fitted with either 4 Ring Pistons or 5 Ring Pistons. Get them out and look. This set is for the 5 Ring Pistons ***

*** These cars were fitted with a choice of two compression ring widths, either 0.063" or 0.078". Get them out and measure. This set is the for the 0.063"wide compression rings **

*** This set is STD (Standard Size), ensure you know the size you require before ordering **

This set contains four times - 

x3 Compression Rings 0.063" wide.

x2 Oil Rings 0.156" wide

The picture shows them in their packet as they are all in order. 

Here’s a new Engine Set of Piston Rings (STD, 5 Ring Type, 0.063"Wide) (Made in the USA by Grant) for the following models from Morris –

(1489cc Engines Only)

MORRIS

Morris Cowley 1500             (1956- 58) (Not Cowley 1200)

*** These cars were fitted with either 4 Ring Pistons or 5 Ring Pistons. Get them out and look. This set is for the 5 Ring Pistons ***

*** These cars were fitted with a choice of two compression ring widths, either 0.063" or 0.078". Get them out and measure. This set is the for the 0.063"wide compression rings **

*** This set is STD (Standard Size), ensure you know the size you require before ordering **

This set contains four times - 

x3 Compression Rings 0.063" wide.

x2 Oil Rings 0.156" wide

The picture shows them in their packet as they are all in order. 

Here's new pair of new Front (x2) & Rear Brake Hoses (x1) for the following models from Morris -  

MORRIS

Morris J Type Van  (1949- 57)

Morris JB Van        (1957- 61)

(Not for the Morris J2 Van)

Here's a new Clutch Slave Cylinder Repair Seals Kit (1.25") for the following models from Morris Vans -

MORRIS

Morris JU250 Van (1600cc Petrol)      (1967- 74)

(** Not for Morris J4 Van or anything else other than what's written above **)

Here’s a new Ignition Tune Up Kit for the following models from Morris -

MORRIS

Morris Minor 1000 (1967- 71)

(Note : Only for Minors after 1967 with a 'Top Entry' cap).

These models have a Lucas 4 Cyl distributor.

This kit includes the following parts -

Distributor Cap

Points

Rotor Arm

Condenser

Here's a new Oil Pump (x1) for the following models from Morris  -

MORRIS

Morris Minor   (1952- 71)

(803cc, 948cc & 1098cc)

The picture shows the Top & Bottom of ONE Oil Pump.